17-4 PH Stainless Steel
(UNS S17400 / AMS 5643 / ASTM A564)
A versatile martensitic precipitation-hardening alloy offering an excellent balance of high strength, good corrosion resistance, and cost-effectiveness. The industry standard for aerospace fasteners, oil & gas valve stems, and precision machined components.
- ✔ AMS 5643 / ASTM A564 Compliant (Revision Locked)
- ✔ Multiple Aging Conditions: H900, H1025, H1075, H1150
- ✔ NACE MR0175 Compliant (H1150 condition for sour service)
- ✔ EN 10204 3.1 / 3.2 MTC with full heat-lot traceability
1. Chemical Composition & Material Properties
17-4 PH (UNS S17400) is a chromium-copper precipitation-hardening martensitic stainless steel. Its high strength and hardness are achieved through a simple, single-step aging heat treatment at relatively low temperatures, minimizing distortion.
| Element | Cr | Ni | Cu | Nb+Ta | Mn | Si | C |
|---|---|---|---|---|---|---|---|
| Range (%) | 15.0–17.5 | 3.0–5.0 | 3.0–5.0 | 0.15–0.45 | ≤ 1.00 | ≤ 1.00 | ≤ 0.07 |
- Cu (Copper): The primary element responsible for precipitation hardening.
- Nb (Niobium): Forms NbC to prevent grain growth and improve toughness.
- Cr (Chromium): Provides corrosion resistance equivalent to 304 stainless steel.
2. Mechanical Performance By Condition
17-4 PH can be aged to various conditions to achieve specific strength-toughness combinations. Typical minimum values per AMS 5643:
| Condition | Tensile Strength | Yield Strength (0.2%) | Elongation | Hardness (HRC) |
|---|---|---|---|---|
| H900 | ≥ 1310 MPa | ≥ 1170 MPa | ≥ 10% | 40–47 |
| H1025 | ≥ 1070 MPa | ≥ 1000 MPa | ≥ 12% | 34–42 |
| H1150 | ≥ 930 MPa | ≥ 720 MPa | ≥ 16% | 28–37 |
3. Corrosion Resistance
17-4 PH provides excellent corrosion resistance, superior to 400-series stainless steels and comparable to 304 stainless in many environments.
For sour oil and gas service (H₂S environments), the H1150 condition is strictly specified to meet NACE MR0175 / ISO 15156 hardness limitations (max 33 HRC).
4. Processing & Welding Performance
- Machining: Best machined in the solution-annealed (Condition A) state. Avoid machining in the H900 condition due to high hardness and tool wear.
- Welding: Can be welded using standard methods. Preheating is generally not required for sections up to 100 mm (4 in.). For very heavy sections or highly restrained joints, a preheat of 100-150°C may be considered to prevent cold cracking. Post-weld solution annealing followed by aging is highly recommended to restore optimal properties.
- Heat Treatment: Solution treat at 1038°C (1900°F), then age at 482°C - 621°C (950°F - 1150°F) depending on desired strength.
5. Wide Range of Applications
- Aerospace: High-strength fasteners, structural components, landing gear parts.
- Oil & Gas: Valve stems, wellhead equipment, pump shafts (H1150 condition).
- Chemical & Food: Pump parts, gears, and shafts requiring both strength and moderate corrosion resistance.
6. 17-4 PH vs 15-5 PH: Which is Right for Your Project?
While 17-4 PH is the industry standard, 15-5 PH was developed to overcome its limitations in heavy sections. Here is the comparison:
| Characteristic | 17-4 PH (UNS S17400) | 15-5 PH (UNS S15500) |
|---|---|---|
| δ-Ferrite Content | Typically 2%–5% (Inherent) | ≤ 2% (Essentially Ferrite-Free) |
| Transverse Toughness | Reduced in heavy sections due to δ-ferrite banding | Significantly Higher & More Uniform |
| MPI Reliability | High risk of false indications from δ-ferrite | Excellent (Eliminates false indications) |
| Cost | Lower (More Economical) | Higher (15% - 50% Premium) |
Cost vs. Performance:
17-4 PH is the most cost-effective choice for small cross-sections (under 3 inches) and standard industrial applications.
However, if your project involves large-section aerospace forgings or strict Magnetic Particle Inspection (MPI) requirements, upgrading to 15-5 PH will eliminate the risk of false indications caused by δ-ferrite banding.




Whatsapp
Whatsapp